Turn any plain pool into a PARTY!
Installation Instructions
WARNING: NO DIVING BY, JUMPING OFF OF, OR UNSUPERVISED CHILDREN WITH THE AQUA-RITA TABLE!
Installing the Aqua-Rita Table is simple and does not require any tools for proper assembly. You're too busy to be messing around with confusing instruction manuals... you have a pool to be in!
01
Place all 4 seat holders in upright position with all the dovetails facing each other forming a square in the middle.
02
Slide the center post into each dovetail at the same time securing it all the way in. Make sure the center post is all the way down, locking in all 4 seat holders so the center post cannot move side to side. (If necessary, wiggle and push down to ensure center post is all the way down).
03
Place the tabletop on top of the grey threaded center post and spin counterclockwise until it is all the way down. Watch to make sure the 2 small holes line up.
04
Once you have seen that the 2 holes have lined up, Insert the knob screw into the hole and turn clockwise until 3/4 of the threads are gone. The black knob should NOT be all the way in and touching the table. See insert as that is as far in as it should go.
05
Remove the black drain plug cap and place the cap inside a cupholder in the Aqua-Rita tabletop. You will need this while you are in the pool so the cupholder is a perfect spot.
06
Make sure tabletop is all the way down. Spin tabletop clockwise until it stops. Take a 5-minute break, put on a swimsuit, and grab a friend! Place a cold drink next to the pool.
07
Place the entire Aqua-Rita into the pool. Try to keep it level while it's filling up with water. This will take 2-3 minutes and should sink by itself. DO NOT pull-on legs as they will come off. Only use center post or the tabletop to apply pressure to speed up the sinking process.
08
Once the base is under the water, you must start to apply pressure. Apply downward pressure on the tabletop until the entire tabletop is under the water. Two people can do this by applying equal pressure on each side.
09
The holes on the outer edge of the tabletop will allow air to escape and will create bubbles. Once the tabletop has been under water for a few minutes, the bubbles will stop. Make sure the bubbles have stopped.
10
Once the bubbles have stopped and with the tabletop still under the water, screw on the drain plug cap and tighten until snug. Do not over tighten the drain plug.
11
Turn tabletop counterclockwise until it rises out of the water. Tabletop MUST be 6-8 inches above water which is where the bottom curve starts. The weight of the tabletop keeps the base from floating around the pool. Hand tighten both hand screws on center post to lock in desired table height.
Necklace not included
12
Relax and let the PARTY begin.
Umbrella not included
If you have any questions about installation, please do not hesitate to contact us at Support@Aquarita.com
THE AQUA-RITA TABLE IS NOT A DIVING BOARD, DANCE FLOOR, OR BABYSITTER!
The Aqua-Rita max height of the tabletop is 5 ft, so the MAX pool depth is 4 ft 6 in.
The Aqua-Rita is designed to be in shallow water and works best on a flat surface.
The Aqua-Rita will handle a slight taper. MAX pool grade is 6 in per every 12 ft length.
Example: 24 ft round pool, 4 ft deep sides to 4.5 ft deep to the center of the pool. The Aqua-Rita would sit on the flattest part of the surface of the pool floor.
Example: Rectangle/oval pool, one side 3.5 ft deep and 5 ft on deep end. The Aqua-Rita would sit on flat shallow side and not on the tapered transition to deep end.
4' Deep
4'6"Deep
12'
4' Deep
12'
5' Deep
Your Aqua-Rita delivery will include:
1 Center Post
1 Threaded Post
1 Table Top
4 Seat Post
4 Seats
3 Knob Screws
Umbrella not included